# # /etc/rc.serial # Initializes the serial ports on your system # # Distributed with setserial version 2.10 # # Standard flags you want your serial devices to have # Examples: SAK, pgrp_lockout, session_lockout # STD_FLAGS="session_lockout" SETSERIAL=/sbin/setserial echo -n "Configuring serial ports...." # Do wild interrupt detection # ${SETSERIAL} -W /dev/cua0 ############################################################### # # AUTOMATIC CONFIGURATION # # Uncomment the appropriate lines below to enable auto-configuration # of a particular board. Or comment them out to disable them.... # # NOTE! Although the automatic configuration is enabled by default, # I strongly suggest that you comment out this section and use the # manual configuration section instead. It's more work to set up, but # it's more reliable. # ############################################################### # Do AUTOMATIC_IRQ probing # AUTO_IRQ=auto_irq # These are the standard COM1 through COM4 devices # # If you have an internal modeme with a Rockwell Chipset, add a "skip_test" # to the /dev/cua3 line below. (It's not added by default because it will # screw up people with 8514 displays). # ${SETSERIAL} /dev/cua0 ${AUTO_IRQ} skip_test autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua1 ${AUTO_IRQ} skip_test autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua2 ${AUTO_IRQ} skip_test autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua3 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # These are for the first AST Fourport board (base address 0x1A0) # ${SETSERIAL} /dev/cua4 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua5 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua6 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua7 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # This enables the new multiport masking feature, which is highly recommened # for AST FourPort boards. # #${SETSERIAL} /dev/cua4 set_multiport port1 0x1BF mask1 0xf match1 0xf # These are for the second AST Fourport board (base address 0x2A0) # ${SETSERIAL} /dev/cua8 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua9 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua10 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua11 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # This enables the new multiport masking feature, which is highly recommened # for AST FourPort boards. # #${SETSERIAL} /dev/cua8 set_multiport port1 0x2BF mask1 0xf match1 0xf # These are the 3rd and 4th ports on the Accent Async board. # #${SETSERIAL} /dev/cua12 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua13 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # Usenet Serial Board II (base address 0x100) # #${SETSERIAL} /dev/cua16 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua17 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua18 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua19 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # BocaBoard 4 port (BB-1004) (base address 0x100) # #${SETSERIAL} /dev/cua16 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua17 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua18 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua19 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # BocaBoard 8 port (BB-1008) (base address 0x100), # or two BB-1004's (base addresses 0x100 and 0x120) # #${SETSERIAL} /dev/cua16 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua17 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua18 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua19 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua20 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua21 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua22 ${AUTO_IRQ} autoconfig ${STD_FLAGS} #${SETSERIAL} /dev/cua23 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # BocaBoard 16 port (BB-1008), (base address 0x100), # or two BB-1008's (base addresses 0x100 and 0x140), # or four BB-1004's (base address 0x100, 0x120, 0x140, and 0x160) # # Warning --- some of these ports may conflict with the Future Domain # SCSI controller. If you want to run both the BocaBoards and the # Future Domain controller, you may need to change the port assignment # of the Bocaboards -- see below in the section on manual configuration. # ${SETSERIAL} /dev/cua16 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua17 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua18 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua19 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua20 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua21 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua22 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua23 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua24 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua25 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua26 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua27 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua28 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua29 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua30 ${AUTO_IRQ} autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua31 ${AUTO_IRQ} autoconfig ${STD_FLAGS} # This enables the new multiport masking feature, which is highly recommened # for Bocaboard ports. Uncomment only the first line if you have a # BB-1004 or BB-1008. Uncomment both lines if you have a BB-2016. # These numbers assume the Bocaboard is located at address 0x100. If you # change this, remember to change the port1 and port2 addresses. # #${SETSERIAL} /dev/cua16 set_multiport port1 0x107 mask1 0xff match1 0 #${SETSERIAL} /dev/cua16 set_multiport port2 0x147 mask2 0xff match2 0 ############################################################### # # MANUAL CONFIGURATION # # If you want to do manual configuration of one or more of your # serial ports, uncomment and modify the relevant lines. # ############################################################### # These are the standard COM1 through COM4 devices # #${SETSERIAL} /dev/cua0 uart 16450 port 0x3F8 irq 4 ${STD_FLAGS} #${SETSERIAL} /dev/cua1 uart 16450 port 0x2F8 irq 3 ${STD_FLAGS} #${SETSERIAL} /dev/cua2 uart 16450 port 0x3E8 irq 4 ${STD_FLAGS} #${SETSERIAL} /dev/cua3 uart 16450 port 0x2E8 irq 3 ${STD_FLAGS} # These are the first set of AST Fourport ports # #${SETSERIAL} /dev/cua4 uart 16450 port 0x1A0 irq 9 fourport ${STD_FLAGS} #${SETSERIAL} /dev/cua5 uart 16450 port 0x1A8 irq 9 fourport ${STD_FLAGS} #${SETSERIAL} /dev/cua6 uart 16450 port 0x1B0 irq 9 fourport ${STD_FLAGS} #${SETSERIAL} /dev/cua7 uart 16450 port 0x1B8 irq 9 fourport ${STD_FLAGS} # These are the second set of AST Fourport ports # #${SETSERIAL} /dev/cua8 uart 16450 port 0x2A0 irq 5 fourport ${STD_FLAGS} #${SETSERIAL} /dev/cua9 uart 16450 port 0x2A8 irq 5 fourport ${STD_FLAGS} #${SETSERIAL} /dev/cua10 uart 16450 port 0x2B0 irq 5 fourport ${STD_FLAGS} #${SETSERIAL} /dev/cua11 uart 16450 port 0x2B8 irq 5 fourport ${STD_FLAGS} # These are the 3rd and 4th ports on the Accent Async board. # #${SETSERIAL} /dev/cua12 uart 16450 port 0x330 irq 4 ${STD_FLAGS} #${SETSERIAL} /dev/cua13 uart 16450 port 0x338 irq 4 ${STD_FLAGS} # These are two spare devices you can use to customize for # some board which is not supported above.... #${SETSERIAL} /dev/cua14 uart XXXXX port XXXX irq X ${STD_FLAGS} #${SETSERIAL} /dev/cua15 uart XXXXX port XXXX irq X ${STD_FLAGS} # These are the ports used for either the Usenet Serial II # board, or the Boca Board 4, 8, or 16 port boards. # # Uncomment only the first 4 lines for the Usenet Serial II board, # and uncomment the first 4, 8, or all 16 lines for the # Boca Board BB-1004, BB-1008, and BB-2016 respectively. # #${SETSERIAL} /dev/cua16 uart 16550A port 0x100 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua17 uart 16550A port 0x108 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua18 uart 16550A port 0x110 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua19 uart 16550A port 0x118 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua20 uart 16550A port 0x120 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua21 uart 16550A port 0x128 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua22 uart 16550A port 0x130 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua23 uart 16550A port 0x138 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua24 uart 16550A port 0x140 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua25 uart 16550A port 0x148 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua26 uart 16550A port 0x150 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua27 uart 16550A port 0x158 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua28 uart 16550A port 0x160 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua29 uart 16550A port 0x168 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua30 uart 16550A port 0x170 irq 12 ${STD_FLAGS} #${SETSERIAL} /dev/cua31 uart 16550A port 0x178 irq 12 ${STD_FLAGS} ########################################################### # # Print the results of the serial configuration process # ########################################################### echo "done." ${SETSERIAL} -bg /dev/cua? /dev/cua??